Click a band on the resistor and pick its colour, or use the menus. To go the other way, type the value you need and the bands paint themselves. Works for 4, 5 and 6 band parts, and for the number codes printed on surface mount resistors.
Find the bands for a value
Reading the Bands
Hold the resistor with the tolerance band on the right. It is usually gold, silver or brown, and often sits slightly apart from the others. Read from the left.
- 4 band: digit, digit, multiplier, tolerance. Common on carbon film parts, 5% gold.
- 5 band: digit, digit, digit, multiplier, tolerance. Precision metal film, usually 1% brown.
- 6 band: as 5 band, plus a temperature coefficient band at the far right.
| Colour | Digit | Multiplier | Tolerance | Temp coefficient |
|---|---|---|---|---|
| Black | 0 | ×1 Ω | - | 250 ppm/K |
| Brown | 1 | ×10 Ω | ±1% | 100 ppm/K |
| Red | 2 | ×100 Ω | ±2% | 50 ppm/K |
| Orange | 3 | ×1 kΩ | - | 15 ppm/K |
| Yellow | 4 | ×10 kΩ | - | 25 ppm/K |
| Green | 5 | ×100 kΩ | ±0.5% | 20 ppm/K |
| Blue | 6 | ×1 MΩ | ±0.25% | 10 ppm/K |
| Violet | 7 | ×10 MΩ | ±0.1% | 5 ppm/K |
| Grey | 8 | ×100 MΩ | ±0.05% | 1 ppm/K |
| White | 9 | ×1 GΩ | - | - |
| Gold | - | ×0.1 Ω | ±5% | - |
| Silver | - | ×0.01 Ω | ±10% | - |
| None | - | - | ±20% | - |
Values per IEC 60062. "None" means no tolerance band, which is ±20% on older parts.
Where You Will Meet Them
Look inside a modern ECU and you will not find a single colour banded resistor. They are all surface mount chips. Banded parts turn up in wiring that someone has added, which on a race car is a lot of it:
- CAN termination. A 120 Ω resistor at each end of the bus, often soldered inline and heatshrunk into a motorsport loom. It is the first thing to check when a newly added logger or dash will not talk.
- Logger and dash inputs. Pull-up resistors so a switch, a temperature sender or an open collector output gives the input a clean voltage.
- Sensor substitutes. A fixed resistor wired in where a sensor has been removed, so the ECU sees a plausible reading instead of logging a fault.
- Older modules and aftermarket kit. Through-hole boards in older ECUs, relays with suppression resistors, and bought-in accessories.
The heavy duty resistors on a car, such as ignition ballast resistors, LED load resistors and blower motor resistor packs, are a different family: wirewound or metal element parts in ceramic or aluminium bodies, with no colour bands.
A colour code tells you what a resistor should be, not what it is. Resistors in looms get heat-cycled and the paint discolours. If a reading matters, measure it out of circuit with a meter, and check the parts around it before blaming the sensor.
Common Questions
Put the tolerance band on the right and read from the left. The tolerance band is usually gold, silver or brown, and on most parts there is a slightly bigger gap before it. Gold and silver are never the first band, so if one end is gold or silver, that end goes on the right.
If it is still ambiguous, read it both ways and see which gives a real value. Red red orange reads 22 kΩ one way round; the other way gives 3.2 kΩ, which is not a standard value.
Three usual reasons:
- Tolerance. A 5% 4k7 can read anywhere from 4.465 kΩ to 4.935 kΩ and still be in spec. The range box above shows the limits.
- Measuring in circuit. Anything else connected across it gives the meter a parallel path, so it reads low. Lift one leg, or unplug the module, before trusting the reading.
- Damage or heat. Overheated resistors drift and the paint darkens, so the colours lie. A resistor that has cooked is suspect whatever it reads.
It is the letter code from IEC 60062, used on circuit diagrams and parts lists. The letter is the multiplier and sits where the decimal point would be, so a smudged or missed decimal point cannot change the value.
- R = ohms: 220R is 220 Ω, 0R47 is 0.47 Ω
- k = thousand: 4k7 is 4.7 kΩ
- M = million: 1M5 is 1.5 MΩ
The value box on this page accepts this format.
A high speed CAN bus (ISO 11898-2) needs a 120 Ω resistor across CAN-H and CAN-L at each of its two ends. That is brown red brown on a 4 band part. Use the preset button above to see it.
With everything powered down you should measure about 60 Ω between CAN-H and CAN-L, because the two 120 Ω resistors are in parallel. About 120 Ω means one end is missing. Well below 60 Ω means an extra terminator or a fault on the bus.
On a motorsport loom where you add a logger or dash to the bus, check whether the device already has termination built in before adding your own.
You can, but only a reading above the tolerance range tells you anything for certain: it means the resistor has gone high or open. A low reading may just be the rest of the circuit in parallel. Always measure with the power off.
For low values, short the meter leads together first and subtract that reading (or use the meter’s relative mode). For values over about 100 kΩ, keep your fingers off both ends, because your body is in parallel with the part.
Four band parts have two significant digits and are usually 5% or 10%. Five band parts have three digits for finer values and are usually 1% or better. Six band parts add a temperature coefficient band, which says how much the value moves per degree, in parts per million per kelvin. 100 ppm/K over a 100 °C rise is a 1% change.
Switch the calculator to SMD code and type what is printed on the part. There are three common systems:
- 3 digit: two digits then the number of zeros. 472 is 47 followed by two zeros, 4.7 kΩ. Usually 5% parts.
- 4 digit: three digits then the number of zeros. 4701 is 470 followed by one zero, 4.7 kΩ. Usually 1% parts.
- EIA-96: two digits and a letter, for 1% parts too small for four digits. The number is a position in the E96 value list and the letter is the multiplier. 01C is 100 × 100, 10 kΩ.
An R in the code is the decimal point: 4R7 is 4.7 Ω. A part marked 0 or 000 is a zero ohm link, used as a jumper.
No, most do not. Power resistors such as ignition ballast resistors, LED indicator load resistors and blower motor resistor packs are wirewound or metal element parts in ceramic or aluminium housings, with the value printed on, if it is marked at all. Resistors on ECU and module circuit boards are surface mount chips with a number code instead of bands.
Colour banded parts mostly turn up in wiring that has been added to the car: motorsport looms, CAN termination, logger and dash inputs, and resistors fitted in place of a removed sensor.