The ECU only knows where the crank is because a toothed wheel tells it, one edge at a time.

Pick a pattern and a sensor, set the rpm, and watch what the ECU sees.

Illustration. The wheel is shown slowed right down; the numbers are at full speed.
One revolution, oldest on the leftShaded band: the missing tooth gap
-
Tooth frequency
-
Time per tooth
-
Interval across the gap
-
Time per revolution

Tooth frequency counts every tooth position, so it is the frequency a scope shows on the normal teeth. Interval figures are edge to edge.

On the Scope

What Good Looks Like

VR: an AC wave centred on zero, one cycle per tooth, with an obvious break where the gap passes. It gets bigger as the engine speeds up, so check it at cranking speed, where it is smallest. The ECU usually triggers on the zero crossing, which is why getting the two wires the right way round matters.

Hall: a square wave switching cleanly between ground and the pull-up voltage, the same height at any speed, with one long low or high period at the gap. Rounded edges, a step that does not reach ground, or noise on the flat parts point to wiring, earth or supply problems rather than the sensor.

Wiring

Typical Connections

By function only. Pin numbers and wire colours change between makers and between versions of the same sensor, so take those from the wiring diagram for the car.

VR (2 wire)Hall (3 wire)
ConnectionsSignal + and signal −. The way round matters: swapped wires shift the timing or stop the ECU syncing.Supply (5 V or 12 V, depending on the sensor), ground and signal.
ScreenOften a screened cable. Earth the screen at the ECU end only.Usually unscreened.
SignalAC voltage made by the sensor itself. No supply needed.Switched to ground by the sensor and pulled up to the supply by the ECU or the sensor.
Quick testScope it while cranking. A meter shows an open or shorted coil; the correct resistance comes from the sensor data.Check for supply and ground at the plug, then scope the signal.
Shapes are illustrative

The traces show the pattern and timing. The Hall scale follows the pull-up you pick; the VR scale is relative, because real VR output differs between sensors and makers and rises with speed, so there is no single typical voltage. It also falls as the air gap grows. Compare against a known good car, or the sensor and ECU data, before condemning a part.

FAQ

Common Questions

The gap is the once-per-revolution reference. The ECU times every tooth. When one interval comes in at about two or three times the one before, it knows the gap has just passed, and from then on it counts teeth to know exactly where the crank is.

Where TDC sits relative to the gap differs between engines and ECUs. Take it from the ECU or engine data, never from a picture of a different wheel.

The first number is the tooth positions spaced around the wheel, the second is how many are left out. A 60-2 wheel has 60 positions 6° apart with two missing, so 58 real teeth. A 36-1 has 36 positions 10° apart with one missing. More teeth give the ECU finer angle resolution; fewer are easier to machine and to read at low speed.

A VR (variable reluctance) sensor is a magnet and coil. It makes its own AC voltage, so it needs no supply, and usually has two wires, sometimes with a screen. The voltage rises with speed and drops as the air gap grows.

A Hall sensor needs a supply. It normally has three wires: supply, ground and signal, and switches the signal between ground and the pull-up voltage, giving a square wave whose height does not change with speed. Whether it reads high or low on a tooth depends on the sensor.

Confirm with the wiring diagram or a scope, not by counting pins alone.

Cranking is where a weak crank signal shows up. A VR signal is smallest at cranking speed, so a large air gap, a damaged or swarf-covered sensor tip, or slow cranking can leave it below what the ECU needs. Swap the two VR wires and the ECU triggers on the wrong side of each tooth, which shifts the timing or stops it syncing. A chipped tooth or a bent wheel gives an extra short or long interval that the ECU can mistake for the gap.

A scope on the sensor while cranking answers most of these in one look.

No. The crank turns twice per four-stroke cycle, so the crank wheel alone cannot tell compression from exhaust. Wasted spark and batch injection can run on the crank alone. Sequential injection and coil-on-plug need a cam signal as well.

Analogue Sensor Scaling DTC Code Search - crank and cam position codes

Engineered By Design is a participant in the Amazon EU Associates Programme, an affiliate advertising programme designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.co.uk. Product links marked with “Buy on Amazon” may earn EBD a small commission at no extra cost to you.